Skip to main content

Should I Turn Off The Energy-Saving Lighting Often?

To combat the cost of electricity, we are switching to energy-saving lightbulbs, which are mostly fluorescent lighting.

There are a few myths related to fluorescent lighting that prompts us asking this questions:
 Should I turn off the light when leaving the room?

The short answer is yes. Turn them off if you will be gone for more than 10 minutes. 


Myth #1: It takes more energy to start a fluorescent that it does to run it, so leave the lights on all the time to save money on your electric bill.

Reality: When you turn on a fluorescent lamp, there is a very brief jump in current when the ballast charges the cathodes and causes the lamp to start. This inrush of current can be many times greater than the normal operating current of the lamp. However, the spike of current draw normally lasts no longer than 1/10th of a second, and draws the equivalent of about 5 seconds of normal operation. So, if you turn your fluorescent lamp off and on more frequently than every 5 seconds, you will use more power than normal. So, normal switching of fluorescent lamps has very, very, very little effect on a power bill.


Myth #2: Turning fluorescent lamps off and on wears them out right away.

Reality: Electric lights have a published rating for expected life. This rating is in the hundreds of hours for many incandescent lights, and in the thousands of hours for most fluorescents. Fluorescent lights have a life rating based on how many hours they are left on every time they are turned on. This is usually referred to as "burn time", and for fluorescent lights the burn time is three hours.
Every time a fluorescent light is turned on, a tiny amount of the coating on the electrodes is burned off. Eventually, enough coating is burned off, and the lamp fails to start. Most full-size fluorescent lamps are rated to last 20,000 hours when left on for 3 hours every time they are turned on. This means that the lamp has roughly 6,667 starts available to use up. (20,000/3 = 6,667)

Longer burns extend lamp life. If you "burn" your fluorescent lamps shorter than 3 hours per start, you use up your potential starts faster. If you "burn" them longer than 3 hours per start, you use up your starts more slowly. However, you are paying energy costs for the operating time of the lamps, and the most efficient lamp is the one that is not on when it is not needed.

But longer burns use more energy. Operating a light when it is not needed is simply spending money for no purpose. Today's rapidly rising electric rates mandate that every building becomes leaner with energy use to control costs.

So I guess we have to find the trade off point.  There is a point where the amount of money you save from turning off the light exceeds the cost of reducing lamp life by more frequent This is too technical and for me it is not worth to worry about it.

If you like to read it futher, please see the site below.  I grabed more information from there and it explains in great details on the site.

* Information obtained from Lighting Design Lab.

Comments

Popular posts from this blog

Box Hill High School Zone

Parents are struggling with moving into a good reputable school for their kid(s). Here is the zone for Box Hill High School.   Good luck with house hunting!

Brivis Heater - Error Code #69

My Brivis HX23 Heater broke down this week.  H01 Code #69.  This code was not even listed in the User Manual!  Searching around the web and here is what I found: Secret Reset: This is not in the User Manual.  On the networker controller press FUNCTION > 1 > 4 keys and the screen will go blank and come back on after 30 seconds, this has rebooted the main PCB and reset the fault code. Use this with caution as too much gas build up could cause an explosion. Use it only after the unit has enough time to air out the gas build up. What is Code #69 or any other unpublished codes?  The best way to find out is to open up the heater unit.   There is a little LCD on the PCB showing what error exactly is. (Note: Opening up the unit may void your warranty.)

The Bose Soundbar 700 Won't Connect to App

Bose has one of the best speaker sound. I learnt about Bose more than 25 years ago and still a fan.  I bought Soundbar 700 in 2018.  It took me a while to set it up but it has been giving me troubles once a while.  Recently, I was not able to connect Soundbar 700 with my phone.  Done the factory reset on the soundbar, it didn't work. I spent hours reseting everything multiple times and finally I found this article,  https://www.bose.com.au/en_au/support/articles/HC1380/productCodes/bose_soundbar_700/article.html .  Tweaking them all and finally got it to work again. I think the most important setting is to TURN WPS OFF on the router!  Hope it helps.